led_effects.cpp 6.6 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
#include "led_effects.h"
/*****************************************************************
 * Configuration                                                 *
 *****************************************************************/
namespace config {
  const uint8_t max_brightness = MAX_BRIGHTNESS;
  const uint8_t min_brightness = MIN_BRIGHTNESS;
  const int kitt_tail = 3; // How many dimmer LEDs follow in K.I.T.T. wheel
}

/*****************************************************************
 * Configuration  (calculated from above values)                 *
 *****************************************************************/
namespace config  //TODO: Use a class instead. NightMode could then be another state.
{
  const float average_brightness = 0.5 * (config::max_brightness + config::min_brightness);
  const float brightness_amplitude = 0.5 * (config::max_brightness - config::min_brightness);
  bool night_mode = false;
}

21
22
#if defined(ESP8266)
// NeoPixels on GPIO05, aka D1 on ESP8266.
23
const int NEOPIXELS_PIN = 5;
24
25
26
27
28
#elif defined(ESP32)
// NeoPixels on GPIO23 on ESP32. To avoid conflict with LoRa_SCK on TTGO.
const int NEOPIXELS_PIN = 23;
#endif

29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
const int NUMPIXELS = 12;
//NOTE: One value has been prepended, to make calculations easier and avoid out of bounds index.
const uint16_t CO2_TICKS[NUMPIXELS + 1] = { 0, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, 1800, 2000, 2200 }; // [ppm]
// For a given LED, which color should be displayed? First LED will be pure green (hue angle 120°),
// last 4 LEDs will be pure red (hue angle 0°), LEDs in-between will be yellowish.
const uint16_t LED_HUES[NUMPIXELS] = { 21845, 19114, 16383, 13653, 10922, 8191, 5461, 2730, 0, 0, 0, 0 }; // [hue angle]
Adafruit_NeoPixel pixels(NUMPIXELS, NEOPIXELS_PIN, NEO_GRB + NEO_KHZ800);

namespace counter {
  uint16_t wheel_offset = 0;
  uint16_t kitt_offset = 0;
  uint16_t breathing_offset = 0;
}  // namespace counter

namespace LedEffects {
  //On-board LED on D4, aka GPIO02
  const int ONBOARD_LED_PIN = 2;

  void setupOnBoardLED() {
    pinMode(ONBOARD_LED_PIN, OUTPUT);
  }

  void onBoardLEDOff() {
    digitalWrite(ONBOARD_LED_PIN, HIGH);
  }

  void onBoardLEDOn() {
    digitalWrite(ONBOARD_LED_PIN, LOW);
  }

  void setupRing() {
    pixels.begin();
    pixels.setBrightness(config::max_brightness);
    pixels.clear();
  }

  void toggleNightMode() {
    config::night_mode = !config::night_mode;
    if (config::night_mode) {
      Serial.println(F("NIGHT MODE!"));
      pixels.clear();
      pixels.show();
    } else {
      Serial.println(F("DAY MODE!"));
    }
  }

  //NOTE: basically one iteration of KITT wheel
  void showWaitingLED(uint32_t color) {
    delay(80);
    if (config::night_mode) {
      return;
    }
    pixels.clear();
    for (int j = config::kitt_tail; j >= 0; j--) {
      int ledNumber = abs((counter::kitt_offset - j + NUMPIXELS) % (2 * NUMPIXELS) - NUMPIXELS) % NUMPIXELS; // Triangular function
      pixels.setPixelColor(ledNumber, color * pixels.gamma8(255 - j * 76) / 255);
    }
    pixels.show();
    counter::kitt_offset += 1;
  }

  // Start K.I.T.T. led effect. Red color as default.
  // Simulate a moving LED with tail. First LED starts at 0, and moves along a triangular function. The tail follows, with decreasing brightness.
  // Takes approximately 1s for each direction.
  void showKITTWheel(uint32_t color, uint16_t duration_s) {
    pixels.setBrightness(config::max_brightness);
    for (int i = 0; i < duration_s * NUMPIXELS; ++i) {
      showWaitingLED(color);
    }
  }

  /*
   * For a given CO2 level and ledId, which brightness should be displayed? 0 for off, 255 for on. Something in-between for partial LED.
   * For example, for 1500ppm, every LED between 0 and 7 (500 -> 1400ppm) should be on, LED at 8 (1600ppm) should be half-on.
   */
  uint8_t getLedBrightness(uint16_t co2, int ledId) {
    if (co2 >= CO2_TICKS[ledId + 1]) {
      return 255;
    } else {
      if (2 * co2 >= CO2_TICKS[ledId] + CO2_TICKS[ledId + 1]) {
        // Show partial LED if co2 more than halfway between ticks.
        return 27; // Brightness isn't linear, so 27 / 255 looks much brighter than 10%
      } else {
        // LED off because co2 below previous tick
        return 0;
      }
    }
  }

  /**
   * Fills the whole ring with green, yellow, orange or black, depending on co2 input and CO2_TICKS.
   */
  void displayCO2color(uint16_t co2) {
    if (config::night_mode) {
      return;
    }
    pixels.setBrightness(config::max_brightness);
    for (int ledId = 0; ledId < NUMPIXELS; ++ledId) {
      uint8_t brightness = getLedBrightness(co2, ledId);
      pixels.setPixelColor(ledId, pixels.ColorHSV(LED_HUES[ledId], 255, brightness));
    }
    pixels.show();
  }

  void showRainbowWheel(int duration_s, uint16_t hue_increment) {
    if (config::night_mode) {
      return;
    }
    unsigned long t0 = seconds();
    pixels.setBrightness(config::max_brightness);
    while (seconds() < t0 + duration_s) {
      for (int i = 0; i < NUMPIXELS; i++) {
        pixels.setPixelColor(i, pixels.ColorHSV(i * 65535 / NUMPIXELS + counter::wheel_offset));
        counter::wheel_offset += hue_increment;
      }
      pixels.show();
      delay(10);
    }
  }

  void redAlert() {
    if (config::night_mode) {
      onBoardLEDOn();
      delay(500);
      onBoardLEDOff();
      delay(500);
      return;
    }
    for (int i = 0; i < 10; i++) {
      pixels.setBrightness(static_cast<int>(config::max_brightness * (1 - i * 0.1)));
      delay(50);
      pixels.fill(color::red);
      pixels.show();
    }
  }

  void breathe(int16_t co2) {
    if (!config::night_mode) {
      //TODO: use integer sine
      pixels.setBrightness(
          static_cast<int>(config::average_brightness
              + cos(counter::breathing_offset * 0.1) * config::brightness_amplitude));
      pixels.show();
      counter::breathing_offset += 1;
    }
    delay(co2 > 1600 ? 50 : 100);  // faster breathing for higher CO2 values
  }

  /**
   * Displays a complete blue circle, and starts removing LEDs one by one. Returns the number of remaining LEDs.
   * Can be used for calibration, e.g. when countdown is 0. Does not work in night mode.
   */
  int countdownToZero() {
    if (config::night_mode) {
      Serial.println("Night mode. Not doing anything.");
      delay(1000); // Wait for a while, to avoid coming back to this function too many times when button is pressed.
      return 1;
    }
    pixels.fill(color::blue);
    pixels.show();
    int countdown;
    for (countdown = NUMPIXELS; countdown >= 0 && !digitalRead(0); countdown--) {
      pixels.setPixelColor(countdown, color::black);
      pixels.show();
      Serial.println(countdown);
      delay(500);
    }
    return countdown;
  }
}